- Do I need a special bulb for my pool light?
- Can a pool light electrocute you?
- Are pool lights universal?
- Why does my pool light keep going out?
- Can a 12v pool light electrocute you?
- What is a Nicheless pool light?
- Are pool lights worth it?
- How do I change my pool light without draining the water?
- How do I know if my pool light is 12v or 120v?
- How long does an LED pool light last?
- What happens if water gets into pool light?
- How much does it cost to replace a pool light?
- Does a pool light need a GFCI?
- How many amps does a pool light draw?
- How long does a pool light last?
- How many watts does my pool light need?
- How do I test my pool light?
- How do you fix a leaky pool light?
Do I need a special bulb for my pool light?
@OP, any 120VAC LED bulb should work.
Just make sure it will fit your existing light fixture.
Also, it is a MUST to replace the gasket every time you open the fixture and/or replacing the bulb..
Can a pool light electrocute you?
Faulty bonding/grounding is the cause of many pool electrocution incidents. Pool lights don’t have to be on to be a potential hazard. … This can send electricity through a pool light even if it’s not on during the daytime. Anything that has electricity running to it AND is underwater is a potential hazard.
Are pool lights universal?
It’s universal, because it will fit into most any other pool light niche. And, unlike other lamps that void the warranty or remove the UL listing when installed in other niches, the Hayward Universal LED pool light is UL listed as safe for use in nearly any light niche.
Why does my pool light keep going out?
Chlorine exposure or old age can deteriorate the rubber to warp so that it allows water to reach the light internals. A fixture filled with water can also cause a breaker to trip, so be mindful of that when troubleshooting. … Another less likely cause of a pool light fixture leak is a power cord conduit seal leak.
Can a 12v pool light electrocute you?
Because these lights operate at a very low voltage, they are less inherently dangerous when taken on their own. Some believe the 120 volts generated by an incandescent light can introduce a fatal charge, whereas the power from low-voltage lights, generally 12 volts, can injure but not kill.
What is a Nicheless pool light?
A nicheless led pool light is very energy efficient. Usually, the lights draw only 9 – 30w at 120 volts alternating current. Just like many other low-voltage lightings, this light uses a transformer for power that is 120 VAC to 12- 14 VAC.
Are pool lights worth it?
An LED light will save you roughly 75% on your energy usage compared to a comparable incandescent light. REMEMBER, that LED pool lights cost more, on average, than a simple incandescent light so your cost savings will not start till you recoup the additional money that you spent on the LED lights.
How do I change my pool light without draining the water?
There is no need to lower the water level in your pool to replace the burned-out bulb. Instead, you can remove the light housing from the side of the pool, pull the fixture up onto the side of the pool, and change the light bulb there.
How do I know if my pool light is 12v or 120v?
Check the back of the light housing where the cord connects into the light, there will be a label specification of your light. The brightness of a 12V and 120V will be the same.
How long does an LED pool light last?
about 30,000 hoursLED bulbs have a very long life span…about 30,000 hours compared to the 5,000 hours of the incandescent and the 6,000 hours fiber optics. That’s the equivalent of SIX incandescent replacements and FIVE fiber optic replacements.
What happens if water gets into pool light?
Pool Clown Once the water reaches the socket, it will trip the GFI and that will be the extent of the shock hazard. You should change the (lens) gasket in the fixtures and see if that is the source of the leak, it could also be where the cord enters the fixture.
How much does it cost to replace a pool light?
Total Cost to Install a LED Pool LightDescriptionOptionalCostLED Pool Light FittingNo$150 to $650New TransformerYes$30 to $80ElectricianNo$100 to $400Total Cost$250 to $1130Jun 3, 2014
Does a pool light need a GFCI?
Ground Fault Circuit Interrupters The pool light must be installed on a GFCI circuit. That means that the wires coming to the pool light J-box must come from a GFCI breaker. … The outlet serves as secondary protection to the breaker, both will trip if they sense a voltage variance, or voltage going to ground.
How many amps does a pool light draw?
Pool Lights: 12v, 3.5 watts each. Self-Contained Hot Tub: 240v 50 amps. Automatic Pool Cover: 220v, 5-7 amps OR 110v, 11-13 amps.
How long does a pool light last?
Your pool lighting should give you few problems overall. Most incandescent bulbs will burn for 1,000 hours before bulb replacement is necessary. LED bulbs can burn for 25 years or more (or so they tell us).
How many watts does my pool light need?
The power consumption of illuminators – about 200 watts – is higher than LED lights which are usually about 25 watts for spa lights and 50 watts for pool lights.
How do I test my pool light?
Set your volt-ohm meter to “continuity test” (or lowest ohm scale), and test between the black and white wires to the light (they connect to the bulb). If your light bulb is in good condition, it should read about 3-20 ohms.
How do you fix a leaky pool light?
If your pool water level has dropped down below the skimmer, below the returns and has stabilized at the top of the pool light, you probably have a leak in the pool light conduit behind the pool light. To repair, reach down and remove the screw at 12 o’clock and pull the light out of the light housing, aka light niche.